氟硅改性无溶剂聚氨酯涂层的制备及性能研究

doi:10.19677/j.issn.1004-7964.2023.01.003

皮革科学与工程 ›› 2023, Vol. 33 ›› Issue (1): 15-20.doi: 10.19677/j.issn.1004-7964.2023.01.003

氟硅改性无溶剂聚氨酯涂层的制备及性能研究

孙哲¹, 任松¹, 方剑¹, 范浩军^2,*, 高强²

1.苏州大学纺织与服装工程学院,江苏苏州 215123;
2.四川大学轻工科学与工程学院,四川成都 610065

收稿日期:2022-05-31 出版日期:2023-02-01 上线日期:2023-01-04
通讯作者: *范浩军（1965-）,男,教授,主要从事功能高分子材料及功能皮革。Tel:13668242559,E-mail：fanhaojun@scu.edu.cn。
作者简介:孙哲（1990-）,男,博士,讲师,主要从事皮革/合成革用环境友好高分子涂层材料、基于皮革/合成革的智能传感器及智能可穿戴材料。Tel:18202889402,E-mail:sunzhe@suda.edu.cn。
基金资助:
国家自然科学基金（22178238）; 江苏省卓越博士后计划项目（2022ZB555）; 江苏省高等学校基础科学（自然科学）研究项目（22KJB430040）

Preparation and Property of Fluorine-Silicone Modified Solvent-Free Polyurethane Coating

SUN Zhe¹, REN Song¹, FANG Jian¹, FAN Haojun^2,*, GAO Qiang²

1. College of Textile and Clothing Engineering, Soochow University, Suzhou 215123, China;
2. College of Biomass Science and Engineering, Sichuan University, Chengdu 610065, China

Received:2022-05-31 Online:2023-02-01 Published:2023-01-04

摘要/Abstract

摘要： 借助硅氢加成反应将丙烯酸六氟丁酯接枝于含氢硅油侧链,合成了一种氟硅改性剂,并将其用于无溶剂双组分聚氨酯的改性。首先对改性剂的合成工艺进行了优化,然后对其改性后聚氨酯涂层的表面形貌、疏水性及耐磨性进行了研究。结果表明：合成改性剂的最佳反应温度120 ℃、时间12 h、催化剂用量30 mg/kg,在此条件下接枝率可高达89%;表面形貌及元素分析表明,氟、硅元素在聚氨酯中分散性良好;随着PSF添加量的增加,涂层表面粗糙度和水接触角均呈增大趋势,当PSF添加量为7.5%时,涂层表面水接触角可达118.3°耐磨测试表明,随PSF添加量增大,涂层耐磨性先提升后下降,添加量为2.5%时,耐磨性最佳。

关键词: 氟硅改性, 无溶剂聚氨酯, 涂层, 疏水性, 耐磨性

Abstract: A kind of fluorine-silicone modifier (PSF) was synthesized by grafting hexafluorobutyl acrylate onto polydimethylhydrosiloxane via hydrosilylation reaction, and then used for the modification of solvent-free two-component polyurethane. The synthesis process of the modifier was optimized, and the surface morphology, hydrophobicity and abrasion resistance of the PSF modified polyurethane coatings were investigated. Results showed that the optimum reaction temperature, time and catalyst loading were 120 ℃, 12 h and 30 mg/kg, respectively. In this condition, the grafting ratio could reach 89%. Results of surface morphology and elemental analysis showed that the fluorine and silicon elements were well dispersed in the polyurethane coating. The surface roughness and water contact angle (WCA) of the coating exhibited an obvious increase with the addition of PSF. When the PSF loading was 7.5%, the coating’s WCA could reach 118.3°. Results of abrasion resistance test presented that the coating’s abrasion resistance first increased and then decreased with the increase of PSF content, and the best abrasion resistance was achieved with the PSF loading of 2.5%.

Key words: fluorine-silicone modification, solvent-free polyurethane, coating, hydrophobicity, abrasion resistance

中图分类号:

TS529.5

孙哲, 任松, 方剑, 范浩军, 高强. 氟硅改性无溶剂聚氨酯涂层的制备及性能研究[J]. 皮革科学与工程, 2023, 33(1): 15-20.

SUN Zhe, REN Song, FANG Jian, FAN Haojun, GAO Qiang. Preparation and Property of Fluorine-Silicone Modified Solvent-Free Polyurethane Coating[J]. Leather Science and Engineering, 2023, 33(1): 15-20.

参考文献

[1] 范浩军,袁继新.人造革/合成革材料及工艺学[M].北京:中国轻工业出版社,2010.
[2] 徐一剡,章建剑,王旭.水性生态合成革涂饰剂的制备及应用研究[J].皮革制作与环保科技,2022,3(2):7-9.
[3] 张哲. 合成革用水性聚氨酯的制备及工程技术应用研究[D].西安:陕西科技大学,2015.
[4] 冯见艳,王学川,张哲,等.聚氨酯合成革绿色清洁化生产发展趋势分析与探讨[J].皮革科学与工程,2018,28(1):26-30.
[5] Zhang P,Zhou Y,Su H,et al.Hydroxyl-decorated ammonium polyphosphate as flame retardant reinforcing agent in solvent-free two-component polyurethane[J].Polymer International,2017,66(11):1598-1609.
[6] 高静. 合成革用无溶剂聚氨酯面层树脂的制备与应用[D].西安:陕西科技大学,2017.
[7] 蒋文佳,余冬梅,王小君,等.涂层用无溶剂双组份聚氨酯的制备[J].皮革科学与工程,2017,27(6):40-43.
[8] Lv D,Fang N,Zhang W.A PDMS modified polyurethane/Ag composite coating with super-hydrophobicity and low infrared emissivity[J].Infrared Physics&Technology,2020,108:103351.
[9] Król B,Król P,Byczyński L,et al.Methods of increasing hydrophobicity of polyurethane materials:Important applications of coatings with low surface free energy[J].Colloid and Polymer Science,2017,295(12):2309-2321.
[10] Sui Z,Li Y,Guo Z,et al.Preparation and properties of polysiloxane modified fluorine-containing waterborne polyurethane emulsion[J].Progress in Organic Coatings,2022,166:106783.
[11] 张怀文,杜淼,王楠,等.拒水型有机硅改性聚氨酯嵌段共聚物的合成与表征[J].高分子学报,2013(1):63-69.
[12] 陈精华,刘伟区,宣宜宁,等.有机硅改性聚氨酯弹性体材料的研究[J].聚氨酯工业,2004,19(1):12-15.
[13] Zhang W,Jiang S,Lv D.Fabrication and characterization of a PDMS modified polyurethane/Al composite coating with super-hydrophobicity and low infrared emissivity[J].Progress in Organic Coatings,2020,143:105622.
[14] Wen J,Sun Z,Fan H,et al.Synthesis and characterization of a novel fluorinated waterborne polyurethane[J].Progress in Organic Coatings,2019,131:291-300.
[15] Huang Z,Nazifi S,Cheng K,et al.Scalable inter-diffused zwitterionic polyurethanes for durable antibacterial coatings[J].Chemical Engineering Journal,2021,422:130085.
[16] Sun Q,Li H,Xian C,et al.Mimetic marine antifouling films based on fluorine-containing polymethacrylates[J].Applied Surface Science,2015,344:17-26.
[17] Park J M,Lee Y H,Park H,et al.Preparation and properties of UV-curable fluorinated polyurethane acrylates[J].Journal of Applied Polymer Science,2014,131(16):1107-1117.
[18] 李亚萍,隋智慧,郭制安,等.有机氟硅改性水性聚氨酯的合成及应用[J].热固性树脂,2021,36(4):15-19.
[19] 左一杰,李凤艳,蔚红建,等.氟硅复合改性水性聚氨酯的制备及性能研究[J].现代化工,2021,41(1):123-127.
[20] 郑桂凯,陆明,芮小平.有机氟、硅改性水性聚氨酯的研究进展[J].涂料工业,2018,48(7):79-87.
[21] Liu H,Fu B,Li Y,et al.Antigraffiti polyurethane coating containing fluorocarbon side chains grafted polymethylsiloxane[J].Journal of Coatings Technology and Research,2013,10(3):361-369.
[22] 郭松,王梓丞,但年华,等.有机硅改性水性聚氨酯成膜剂的研究[J].中国皮革,2013,42(5):42-44.

氟硅改性无溶剂聚氨酯涂层的制备及性能研究

Preparation and Property of Fluorine-Silicone Modified Solvent-Free Polyurethane Coating

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	赵鹏, 李开军, 陈磊, 刘公岩. “三明治”型有机/无机复合抗菌涂层在皮革表面的稳定构建[J]. 皮革科学与工程, 2023, 33(2): 15-20.
[2]	刘杨, 黄吉进, 张泽天, 李正军. 单宁酸基荧光水性聚氨酯的制备与性能研究[J]. 皮革科学与工程, 2022, 32(6): 39-44.
[3]	陆曼玲, 李阳, 麻寿江, 闫新秀, 刘军, 丁克毅, 陈华林. 基于氢键作用的自修复聚丙烯酸酯乳液的合成及性能[J]. 皮革科学与工程, 2022, 32(3): 59-64.
[4]	肖涵中, 薛妮, 黄亚文, 施丰成, 黄馨, 李东亮, 黄鑫, 石碧. 超疏水香料缓释棉纤维的可控构筑与应用[J]. 皮革科学与工程, 2019, 29(06): 15-19.
[5]	李彬,黄江玲,谢静雅,付丹,韩冰. 汽车座椅PVC革耐磨性影响因素研究[J]. 皮革科学与工程, 2019, 29(04): 40-43.
[6]	梁飞飞;王振亚;王忠辉;范浩军;. 水基聚氨酯回弹性与涂层耐磨性的关系研究[J]. , 2018, 28(06): 5-11.
[7]	马琳;. 阿克隆磨耗机测定橡胶鞋底耐磨性能的不确定度评定[J]. , 2018, 28(06): 46-48.
[8]	李进财;张元智;李国英;. 环氧基有机硅对胶原膜的疏水改性研究[J]. , 2018, 28(05): 5-11.
[9]	于锐权;向俊;李开军;杨正吕;刘公岩;张宗才;. 改性壳聚糖/纳米银复合物对皮革抗菌能力的应用[J]. , 2018, 28(02): 44-48.
[10]	蒋文佳;余冬梅;王小君;龙志云;. 涂层用无溶剂双组份聚氨酯的制备[J]. , 2017, 27(06): 40-43.
[11]	任蕾;杜蕾;何腾飞;白乐;. 鞋用漆皮耐折牢度的影响因素分析研究[J]. , 2017, 27(05): 50-53.
[12]	罗泉清;李开军;刘公岩;彭利华;张宗才;. 聚乙二醇改性壳聚糖作为皮革抗菌涂层的制备及表征[J]. , 2016, 26(01): 28-32.
[13]	张昌龙;滕博;陈武勇;. 微波干燥对皮革涂层性能的影响[J]. , 2013, 23(06): 12-.
[14]	张昌龙;滕博;陈武勇;. 微波干燥对皮革涂层性能的影响[J]. , 2013, 23(06): 12-.
[15]	杨爽;龚英;陈武勇;Lucretia Miu;. 羊皮纸现代复制工艺[J]. , 2012, 22(04): 16-19.